Straw has been used as a building material since time immemorial and has been considered as a waste product from the agricultural sector, usually used for feed, bedding, or fertilization. Nowadays, the construction industry strives to reduce greenhouse gas emissions and is focusing on renewable materials; hence, straw seems to be an attractive, low-energy option. Straw bales or blown insulation are common uses, with limited detailed knowledge regarding the properties of different straw types. Straw is made up of the dry stems of crops. Straw’s chemical composition will differ with different crops and can have a great impact on its effectiveness. As a renewable material, straw also has the potential to be used in buildings, enhancing thermal insulation and reducing environmental impacts. This study considers four kinds of straw: barley, oats, oilseed rape, and triticale, regarding their possible usage in insulation materials. The thermal conductivity, bulk density, and dust generation of each type were tested in the laboratory. Among them, the best performance was shown by the barley straw treated with mechanical pulping using a knife mill at 4000 rpm for 60 s, which showed the lowest bulk density and thermal conductivity and generated the least dust. It is thus proven to be an environmental insulation material with significant implications for sustainable construction and energy-efficient building design, further helping in maintaining environmental sustainability in building construction.
Aging residential buildings in urban areas require effective thermal insulation to enhance energy efficiency and indoor comfort. In Bosnia and Herzegovina (BiH), expanded polystyrene (EPS) is the most commonly used insulation material due to its affordability, despite concerns regarding its flammability and environmental impact. While regulatory changes since 2019 have recommended rock wool for high-rise buildings, the absence of binding fire safety regulations has allowed the continued use of EPS, often driven by financial constraints. This study examines energy efficiency refurbishments in Sarajevo’s high-rise residential buildings and analyze the implications of the partial implementation of recommended measures. Using case studies, surveys, and expert interviews, this research identifies key challenges, such as limited funding, fragmented renovations, and inconsistent coordination between stakeholders. The findings indicate that facade insulation is often prioritized over comprehensive upgrades, including window replacement and heating system improvements, leading to suboptimal energy savings and minimal cost reductions for residents. Additionally, the complexity of multi-apartment ownership structures hinders uniform improvements in energy efficiency. Despite these challenges, property values tend to increase after renovation, highlighting the long-term financial benefits. To maximize energy savings and ensure sustainable urban housing, stronger interdisciplinary collaboration, improved funding mechanisms, and adherence to fire-safety standards are necessary. These measures would enhance the effectiveness of renovations and support long-term energy efficiency strategies.
Smart irrigation systems play a crucial role in water management, particularly in urban greening applications aimed at mitigating urban heat islands and enhancing environmental sustainability. These systems rely on soil moisture sensors to optimize water usage, ensuring that irrigation is precisely tailored to plant needs. This study evaluates the performance of four commercially available capacitive soil moisture sensors—TEROS 10, SMT50, Scanntronik, and DFROBOT—across three different substrates under controlled laboratory conditions. A total of 380 measurements were conducted to assess sensor accuracy, reliability, and the influence of insertion technique on measurement variability. Results indicate that while all sensors adequately cover the moisture ranges critical for plant health, their accuracy varies significantly, highlighting the necessity of substrate-specific calibration. TEROS 10 exhibited the lowest relative deviation and highest measurement consistency, making it the most reliable among the tested sensors. DFROBOT, despite being the least expensive, performed comparably to SMT50 and Scanntronik in certain conditions. The findings provide valuable insights for selecting and calibrating soil moisture sensors in smart irrigation applications, ultimately contributing to improved water efficiency, plant vitality, and sustainable building-integrated greenery.
This paper investigates the potential use of natural materials and elements for stabilizing indoor humidity levels, focusing on creating healthier living environments in buildings. Unstable indoor microclimates, particularly extreme humidity levels, can negatively affect human health by causing issues such as condensation, mold growth, or dry mucous membranes. In this work, we explore how sorptive materials can maintain indoor humidity within the optimal range of 40–50%. The aim is to identify optimal solutions for moisture control using passive elements, such as unfired ceramic components, which demonstrate high sorption activity within the 35–55% relative humidity range. These elements can effectively absorb moisture from, or release it back into, the indoor environment as needed. Five clay types based on different clay minerals were analyzed in the research in order to assess how their structures influence moisture adsorption behavior. These elements can be combined with green/active elements and standard measures, such as ventilation or targeted room air exchange, to improve indoor humidity regulation. The evaluation of the results so far indicates that the use of clay-based elements in the interior offers a sustainable and natural approach to maintaining optimal indoor microclimate conditions. The slab elements from all 5 clay formulations investigated effectively support indoor humidity stabilization.
Thermal insulation materials play a vital role in minimising energy loss in building operation and also affect the amount of greenhouse gas emissions associated with heating and cooling. In this context, it is becoming an increasingly important milestone to find suitable thermal insulation materials that not only meet the technical requirements but also minimise their environmental impact. The trend towards the use of eco-friendly materials for thermal insulation reflects the construction industry’s desire to contribute to environmental protection and the transition to more sustainable models of building construction and renovation. For more than 20 years, a number of research teams have been investigating the possibility of replacing synthetically produced materials such as mineral wool and polystyrene foam with natural fibre-based insulation materials. These alternatives include wood as a traditional, easily renewable raw material. This, together with the low energy intensity of processing and manufacturing wood materials, contributes to its low carbon footprint. Compared to traditional synthetic insulation materials, which are often energy intensive to produce, wood is a more environmentally friendly choice. However, with many European countries now facing a potential shortage of higher quality wood, it is necessary to look for alternative sources of wood, including in the field of thermal insulation materials, materials with a lower carbon footprint that can be produced from lower quality wood or from wood waste that would otherwise only have an energy use. The paper is devoted to the study and use of suitable wood waste and secondary raw materials from spruce wood (coarse wood chips, sawdust and wood flour) for the development of modern thermal insulations with the aim of an environmentally friendly and less energy-intensive production process compared to conventional insulants.
Abstract Research into sustainable construction is increasingly focusing on the use of renewable materials in construction. These materials represent a promising alternative to conventional building materials as they are derived from renewable sources and are usually more environmentally friendly in terms of production, transport and end-of-life treatment. The Department of Ecological Building Technologies at the Vienna University of Technology has been investigating the hygrothermal behaviour and applicability of renewable materials for many years. Not only traditional building materials such as straw, wood, sheep’s wool and hemp have been investigated, but also innovative materials such as mushroom fabric. The research covered various aspects such as moisture protection, fire protection, thermal insulation, durability and resistance to external influences. The overall aim was to deepen the understanding of ecological building materials, overcome barriers to their use, and develop damage-tolerant constructions from them. The robust properties of wheat straw, sheep’s wool, hemp, cellulose and other materials underline their potential as efficient and environmentally friendly building materials. The data and insights gained will not only help to prove the effectiveness of these materials in the construction industry, but also to address concerns and uncertainties about their functionality.
In the validation of microclimate simulation software, the comparison of simulation results with on-site measurements is a common practice. To ensure reliable validation, it is crucial to utilize high-quality temperature sensors with a deviation smaller than the average absolute error of the simulation software. However, previous validation campaigns have identified significant absolute errors, particularly during periods of high solar radiation, possibly attributed to the use of non-ventilated radiation shields. This study addresses the issue by introducing a ventilated radiation shield created through 3D printing, aiming to enhance the accuracy of measurements on cloudless summer days with intense solar radiation. The investigation employs two pairs of sensors, each comprising one sensor with a ventilated and one with a non-ventilated radiation shield, placed on a south-oriented facade with two distinct albedos. Results from the measurement campaign indicate that the air temperature measured by the non-ventilated sensor is elevated by up to 2.8 °C at high albedo and up to 1.9 °C at a low albedo facade, compared to measurements with the ventilated radiation shield. An in-depth analysis of means, standard deviations, and 95% fractiles highlights the strong dependency of the non-ventilated sensor error on wind velocity. This research underscores the importance of employing ventilated radiation shields for accurate microclimate measurements, particularly in scenarios involving high solar radiation, contributing valuable insights for researchers and practitioners engaged in microclimate simulation validation processes.
Due to its ecological and financial benefits, earth building has gained global attention, with earth bricks being extensively used. Shrinkage and crack development have a considerable impact on the performance and quality of earth bricks. This study employs laboratory experiments to examine the shrinkage behavior of earth bricks reinforced with wheat and barley straw. In addition to this, the impact of cement and gypsum additives is examined. The obtained results indicate that increased fiber content reduces crack formation effectively. However, higher levels of cohesive soil have been shown to have a negative influence on shrinkage behavior. In general, higher fiber contents contribute to the improvement of earth brick performance. These findings offer useful insights for improving the composition and characteristics of reinforced earth bricks, resulting in enhanced performance and quality in sustainable construction practices.
There is an increasing demand for green plant walls in indoor environments because of their multifaced benefits, such as aesthetic appeal, indoor air quality improvement, or psychological well-being. Mosses are believed to be excellent for these walls due to their easy application and maintenance. However, so far there is no evidence for their indoor survival. In this study, we tested the moss species Hypnum cupressiforme, Bryachythecium rutabulum, Eurrhynchium angustirete, Thuidium tamariscinum, Streblotrichum convolutum, Syntrichia ruralis, and Ceratodon purpureus for indoor use in living moss walls. We evaluated their vitality through the monitoring of leaf coloration over a twelve month period, subjecting them to varying temperature ranges (14–20 °C), humidity levels (60–100%), and diverse irrigation methods (drip and spray irrigation, 300–1500 mL per day) within controlled climate chambers. Depending on the combination of these variables, mosses survived up to six months. Hypnum cupressiforme and Ceratodon purpureus performed best. However, as the time span of survival was limited, the use of living mosses for indoor purposes at the current stage cannot be recommended. An additional problem is that the requisition of living material such as in the culturing of moss under horticultural conditions is difficult and harvesting from natural environments is detrimental to most habitats.
The use of renewable building materials in construction is crucial to minimising the environmental impact of new buildings. Bio-based building materials have a wide range of positive properties, many of which are due to their hygroscopic behaviour. The purpose of this study is to investigate the hygrothermal performance of chopped straw, sheep’s wool, and cellulose insulated timber frame external wall assemblies in the presence of air leakage and high indoor relative humidity. For this purpose, tests with different moisture contents, overpressures, and defects in the airtight layer were carried out in an outdoor test stand over a period of 18 months. The results were compared with a conventional mineral wool insulated construction. Both sheep’s wool and cellulose are particularly fault-tolerant insulation materials in combination with timber frame constructions. All three bio-based insulations, despite defects in the airtight layer, showed no mould-prone moisture content. An installation level insulated with sheep’s wool can increase the fault tolerance of constructions with insulation made of hygric and more sensitive building materials. For chopped straw and cellulose, the measured U-value was lower than expected. Further in situ measurements of bio-based structures are important to gain confidence in their hygrothermal behaviour and to increase their use in multi-storey construction.
Despite the positive effects of green infrastructure on people and the environment, it is still rarely integrated in public facilities such as schools. The main reason for this is a lack of knowledge about financing options. To fill this gap, the research project MehrGrüneSchulen (Engl.: More Green Schools) develops financing scenarios for green infrastructure in Austrian schools. This case study describes these developed scenarios, which use the principles of crowdsourcing and crowdfunding as well as the newly named principle of chain building. The idea of chain building is to motivate schools that have already successfully financed and built a low-cost greening system to present this process to another school in such a way that they are able to do the same themselves and eventually explain the process to a further school to continue this chain reaction. For the proposed funding scenarios to be effective, there is a need for innovation in education, with a focus on inter-school participation and networking. For this reason, the possible synergies of an online networking platform are discussed, which would help to connect schools and thus further improve the impact of the proposed fundraising processes.
The demand for renewable resources in building construction is increasing, and wheat straw is an excellent option due to its superior environmental performance compared to traditional insulation materials. However, the hygrothermal properties of chopped wheat straw insulation have remained largely unexplored. At the moment, blown-in straw is only blown in vertically, although horizontal blowing would be more efficient depending on the situation. This study investigates the effect of different blowing techniques on the thermal properties of chopped wheat straw insulation, focusing on the difference between vertical and horizontal blowing techniques. In-situ-measured thermal conductivities were compared with design values used in energy balances. In addition, the long-term hygrothermal behavior of chopped wheat straw insulation treated with flame retardants was investigated. The methodology included heat flow plate measurements, needle probe measurements and laboratory measurements using the hot plate method. The results show that there is no significant difference in thermal performance between the blowing techniques. The measured thermal conductivities were lower than expected, challenging the current general normative moisture surcharge on the thermal conductivity of natural fiber insulation. The addition of the flame retardant had no noticeable effect on the hygrothermal properties of the chopped straw. Chopped wheat straw can be regarded as a highly ecological insulation material with great potential for the future.
Contemporary neighborhood livability differs across countries due to implementation of sustainable policies within the building sector. This paper aims to showcase these differences among Germany, Croatia, and Bosnia and Herzegovina through a comparative case study analysis of two contemporary housing developments from each country. Representative neighborhoods from the aforementioned countries that were selected for analysis were located in Munich, Rijeka, and Sarajevo. The residential environment livability analysis method was used in order to pinpoint and compare results of each of these cases, and to assess their livability. The highest number of livability criteria among analyzed cases were found in Munich, while the lowest were found in Sarajevo. The conclusion is that this is happening due to German authorities actually implementing sustainable building standards in housing development prescribed by sustainability policies, while the authorities of Bosnia and Herzegovina completely, and Croatian authorities partially, go around these policies and bend to the will of investors, regulating residential urban development to the detriment of end users.
Heat transfer through building envelopes is a crucial aspect of energy efficiency in construction. Masonry walls, being a commonly used building material, have a significant impact on thermal performance. In recent years, green roofs and walls have gained popularity as a means of improving energy efficiency, reducing urban heat islands, and enhancing building aesthetics. This study aims to investigate the effect of ivy (Hedera helix) greening on heat transfer through masonry walls and their corresponding surface temperatures. Ivy was chosen as a model plant due to its widespread use and ability to cover large surface areas. The results of this study suggest that ivy greening can have a significant impact on the thermal performance of masonry walls. During winter, the heat transfer coefficient of greened walls was found to be up to 30% lower compared to non-greened walls. This indicates that ivy greening can help reduce energy consumption for heating and thus improve the energy efficiency of buildings. In addition, the surface temperature under the ivy was found to be significantly higher than on the bare wall during winter. However, during summer, the surface temperature under the ivy was lower than on the bare wall, which may help reduce cooling energy consumption. The results of this study are consistent with previous research in the field. Overall, this study provides valuable insights into the potential benefits of ivy greening on the thermal performance of masonry walls.
Nema pronađenih rezultata, molimo da izmjenite uslove pretrage i pokušate ponovo!
Ova stranica koristi kolačiće da bi vam pružila najbolje iskustvo
Saznaj više